Все ошибки Infiniti – расшифровка, самодиагностика и удаление

Содержание

Как извлечь коды ошибок
Для автомобилей до 1996 г. в.
Как удалить коды ошибок
Коды ошибок самодиагностики (OBD1)
Коды ошибок (OBD2)
Коды ошибок производителя Infiniti
Общие коды ошибок
Ошибки Infiniti совместимы со следующими моделями

Как извлечь коды ошибок

Автомобили, выпущенные после 1996 года и более поздних годов выпуска оснащены системой OBD2 и требуют использования диагностического сканера для извлечения кодов неисправностей.

Для автомобилей до 1996 г. в.

На моделях G20 ЭБУ расположен за центральной консолью. На моделях J30, M30 и Q45 ЭБУ расположен за задней панелью заднего сиденья.

При возникновении неисправности в ЭБУ/системе впрыска топлива в ЭБУ может быть записан диагностический код неисправности и начнет мигать лампа «Check Engine». Кроме того, в ЭБУ встроена лампа, которая будет мигать одновременно. Чтобы считать код, выполните следующие действия:

Включите зажигание, но не запускайте двигатель.
С помощью небольшой отвертки поверните переключатель режимов диагностики, расположенный на боковой стороне ЭБУ, полностью по часовой стрелке.
Подождите две секунды, затем поверните переключатель в положение против часовой стрелки.
Код неисправности можно считать по длинному (0.6 секунды) миганию, указывающему на первую цифру двухзначного числа, и короткому (0.3 секунды) миганию, указывающему на вторую цифру.

Убедитесь, что диагностический переключатель находится в полном положении против часовой стрелки, когда автомобиль эксплуатируется.

Как удалить коды ошибок

Если используется сканирующий прибор, то для удаления кодов следуйте инструкциям производителя прибора.
Второй, хотя и более трудоемкий способ очистки кодов заключается в том, что с помощью небольшой отвертки нужно полностью повернуть по часовой стрелке переключатель режимов диагностики, расположенный на боковой стороне ECM/ECU. Подождав две секунды, поверните переключатель в положение против часовой стрелки. Диагностика завершится, и память будет очищена.

Коды ошибок самодиагностики (OBD1)

Код ошибки	Описание
11	Crank Angle Sensor
12	Mass Air Flow Sensor
13	ECT Sensor
14	Vehicle Speed Sensor
16	TCS Signal
21	Ignition Signal Circuit
25	Idle Air Control Valve
22	Fuel Pump Control
31	ECM
32	EGR Function
33	Heated Oxygen Sensor
34	Knock Sensor
35	EGR Temperature Sensor (RH)
41	Intake Air Temperature Sensor
42	Fuel Pump Sensor
43	Throttle Position Sensor
45	Injector Leak
46	Secondary Throttle Sensor
51	Injector Analysis
53	EGR Temperature Sensor (LH)
54	Signal Circuit From A/T Control Unit To ECM
65-71	Single Cylinder Or Multiple Cylinder Misfire
72	Three Way catalyst Function
76	Fuel Injection System Function
77	Rear Heated Oxygen Sensor
82	Crankshaft Position Sensor
84	A/T Diagnosis Communication Line
91	Front Heated Oxygen Sensor Heater
103	Park/Neutral Position Switch
105	EGR & Canister Control Solenoid

Коды ошибок (OBD2)

Коды ошибок производителя Infiniti

Код ошибки	Описание
P1031	Heated oxygen sensor (H02S), bank 1, heater – voltage low
P1032	Heated oxygen sensor (H02S), bank 1, heater – voltage high
P1051	Heated oxygen sensor (H02S), bank 2, heater – voltage low
P1052	Heated oxygen sensor (H02S), bank 2, heater – voltage high
P1065	Engine control module (ECM) – battery voltage supply
P1078	Camshaft position (CMP) sensor, exhaust – low voltage
P1084	Camshaft position (CMP) sensor, exhaust – high voltage
P1087	VVEL Small Event Angle Malfunction Bank 1
P1088	VVEL Small Event Angle Malfunction Bank 2
P1089	VVEL Control Shaft Position Sensor Bank 1 Circuit
P1090	VVEL Actuator Motor Bank 1
P1091	VVEL Actuator Motor Relay Circuit
P1092	VVEL Control Shaft Position Sensor Bank 2 Circuit
P1093	VVEL Actuator Motor Bank 2
P1102	Mass air flow (MAF) sensor – performance problem
P1103	MAP Sensor High Voltage
P1104	MAP Sensor Low Voltage
P1105	MAP — BARO switching valve — circuit malfunction
P1110	Intake valve timing control solenoid, bank 1 – malfunction
P1111	Intake valve timing control solenoid, bank 1 – circuit malfunction
P1119	Engine coolant temperature (ECT) sensor, radiator – circuit malfunction
P1120	Throttle position (TP) circuit malfunction
P1121	Throttle motor – malfunction
P1122	Throttle motor – circuit malfunction
P1123	Throttle motor relay – circuit malfunction
P1124	Throttle motor – short circuit
P1125	Throttle position (TP) sensor 1 & 2 — signal malfunction
P1126	Throttle motor – open circuit
P1128	Throttle motor – short circuit
P1130	Intake manifold air control solenoid – malfunction
P1131	Intake manifold air control solenoid – malfunction
P1132	Swirl Control Valve Circuit
P1135	Intake valve timing control solenoid, bank 2 – malfunction
P1136	Intake valve timing control solenoid, bank 2 – circuit malfunction
P1137	Swirl Control Valve Control Position Sensor Circuit
P1138	Swirl Control Valve Control System Performance
P1140	Camshaft position (CMP) actuator LH – circuit malfunction
P1143	Heated oxygen sensor (H02S) 1, bank 1 – voltage low
P1144	Heated oxygen sensor (H02S) 1, bank 1 – voltage high
P1145	Camshaft position (CMP) actuator RH – circuit malfunction
P1146	Heated oxygen sensor (H02S) 2, bank 1 – voltage low
P1147	Heated oxygen sensor (H02S) 2, bank 1 – voltage high
P1148	Closed loop control, bank 1 – inoperative
P1163	Heated oxygen sensor (H02S)
P1164	Heated oxygen sensor (H02S) 1, bank 2 – voltage high
P1165	Intake manifold air control system -vacuum check switch circuit malfunction
P1166	Heated oxygen sensor (H02S) 2, bank 2 – voltage high
P1167	Heated oxygen sensor (H02S) 2, bank 2 – voltage high
P1168	Closed loop control LH – inoperative
P1195	Engine Does Not Start
P1196	Poor Engine Power
P1197	Low Input From Fuel Level Sensor
P1210	Traction control system — malfunction
P1211	ABS/TCS control module – communication malfunction
P1212	ABS/TCS control module – circuit malfunction
P1217	Engine over temperature
P1220	Fuel pump control module – circuit malfunction
P1223	Throttle position (TP) sensor 2 -voltage low
P1224	Throttle position (TP).sensor 2 – voltage high
P1225	Throttle motor position sensor – learning problem, voltage low
P1226	Throttle motor position sensor – learning problem
P1227	Accelerator pedal position (APP) sensor 2 – voltage low
P1228	Accelerator pedal position (APP) sensor 2 – voltage high
P1229	Engine control module (ECM) – sensor supply voltage low/high
P1233	Electronic throttle control – performance
P1234	Throttle motor position sensor – learning problem, voltage low, bank 2
P1235	Throttle motor position sensor – learning problem, bank 2
P1236	Throttle control motor – short circuit
P1238	Throttle control motor – malfunction
P1239	Throttle position (TP) – performance
P1271	Heated oxygen sensor (H02S), bank 1 – voltage low
P1272	Heated oxygen sensor (H02S), bank 1 – voltage high
P1273	Heated oxygen sensor (H02S), bank 1 – lean mixture
P1274	Heated oxygen sensor (H02S), bank 1 – rich mixture
P1276	Heated oxygen sensor (H02S), bank 1 – activity
P1277	Air Fuel Ratio Sensor 1 Bank 1 Circuit Slow Response
P1278	Heated oxygen sensor (H02S), bank 1 – slow response
P1279	Heated oxygen sensor (H02S), bank 1 – slow response
P1281	Heated oxygen sensor (H02S), bank 2 – voltage low
P1282	Heated oxygen sensor (H02S), bank 2 – voltage high
P1283	Heated oxygen sensor (H02S), bank 2 – lean mixture
P1284	Heated oxygen sensor (H02S), bank 2 – rich mixture
P1286	Heated oxygen sensor (H02S), bank 2 – activity
P1288	Heated oxygen sensor (H02S), bank 2 – slow response
P1289	Heated oxygen sensor (H02S), bank 2 – slow response
P1290	Throttle control motor relay – voltage low
P1320	Ignition signal – circuit malfunction
P1335	Crankshaft position (CKP) sensor – circuit malfunction
P1336	Crankshaft position (CKP) sensor- signal malfunction
P1400	Exhaust gas recirculation (EGR) valve — voltage incorrect
P1401	Exhaust gas recirculation temperature (EGRT) sensor – circuit malfunction
P1402	Exhaust gas recirculation (EGR) system – excessive flow
P1421	Cold start emission control – malfunction
P1440	Evaporative emission (EVAP) canister purge control system – small leak
P1441	Evaporative emission (EVAP) canister purge control system – small leak
P1442	Evaporative emission (EVAP) canister purge system – small leak
P1443	Evaporative emission (EVAP) canister purge control system — circuit malfunction
P1444	Evaporative emission (EVAP) canister purge control system – malfunction
P1445	Evaporative emission (EVAP) canister purge control valve — circuit malfunction
P1446	Evaporative emission (EVAP) canister purge control valve – malfunction
P1447	Evaporative emission (EVAP) canister purge control system – malfunction
P1448	Evaporative emission (EVAP) canister purge control valve – malfunction
P1456	Evaporative emission (EVAP) canister purge system – very small leak
P1464	Fuel gauge tank sensor- voltage high
P1480	Engine coolant blower motor control – circuit malfunction
P1490	Evaporative emission (EVAP) canister purge control system – malfunction
P1491	Evaporative emission (EVAP) canister purge control system – malfunction
P1492	Evaporative emission (EVAP) canister purge control valve — malfunction
P1493	Evaporative emission (EVAP) canister purge control valve — malfunction
P1550	Battery condition sensor – malfunction
P1551	Battery condition sensor – low voltage
P1552	Battery condition sensor – high voltage
P1553	Battery condition sensor – signal too high
P1554	Battery condition sensor – signal too low
P1564	Cruise control master switch – circuit malfunction
P1568	Cruise control master switch – signal out of specification
P1572	Cruise control brake pedal switch – circuit malfunction
P1574	Cruise control vehicle speed sensor – signal malfunction
P1605	AT diagnosis communication -signal failure
P1610	Ignition key/engine control module (ECM) – malfunction
P1611	Immobilizer control module/engine control module (ECM) – coding
P1612	Immobilizer control module/engine control module (ECM) communication – malfunction
P1613	Engine control module (ECM), immobilizer function – internal failure
P1614	Immobilizer control module/module coding plug communication – no signal
P1615	Ignition key/immobilizer control module communication – malfunction
P1700	CVT shift control – malfunction
P1701	Transmission Control Module Power Supply
P1702	Transmission Control Module RAM
P1703	Transmission Control Module ROM
P1704	Transmission Control Module
P1705	AT- throttle position (TP) sensor- voltage high or low
P1706	Park/neutral position (PNP) switch – circuit malfunction
P1710	Automatic Transmission Fluid Temperature Sensor Circuit.
P1715	Automatic transmission turbine shaft speed (TSS) sensor- circuit malfunction
P1716	AT – turbine revolution sensor- circuit malfunction
P1720	Vehicle speed sensor (VSS) – signal variation
P1721	Vehicle Speed Sensor MTR
P1722	Estimated Vehicle Speed Signal
P1726	Electric Throttle Control System
P1730	AT- fail safe function -circuit malfunction
P1731	A/T 1st Engine Brake
P1740	CVT lock-up select solenoid valve – malfunction
P1752	AT – input clutch – solenoid valve malfunction
P1754	AT- input clutch- solenoid valve malfunction
P1757	AT- front brake- solenoid valve malfunction
P1759	AT -front brake – solenoid valve malfunction
P1760	AT- overrun clutch solenoid – voltage low
P1762	AT- direct clutch- solenoid valve malfunction
P1764	AT- direct clutch – solenoid valve malfunction
P1767	AT- high/low reverse solenoid valve – malfunction
P1769	AT – high/low reverse solenoid valve – malfunction
P1772	AT – low coast brake solenoid valve – malfunction
P1774	AT – low coast brake solenoid valve – malfunction
P1775	Torque Converter Clutch Solenoid Valve
P1776	Ignition Retard Request Duration Fault
P1777	CVT step motor – circuit malfunction
P1778	CVT step motor – mechanical malfunction
P1780	AT- shift change – signal malfunction
P1800	Intake manifold air control solenoid – circuit malfunction
P1801	Variable Intake Air System Control Solenoid Valve 2
P1805	Brake pedal position (BPP) switch – circuit malfunction
P1807	Vehicle Speed Sensor A/T
P1808	Vehicle Speed Sensor ABS
P1810	4 LO Switch
P1813	4WD Shift Switch
P1814	Wait Detection Switch
P1815	Manual Mode Switch
P1816	Park/Neutral Position Switch
P1817	Actuator Motor
P1818	Actuator Position Switch
P1819	Transfer Control Device
P1820	Engine Speed Signal
P1841	Automatic Transmission Fluid Pressure Switch 1
P1843	Automatic Transmission Fluid Pressure Switch 3
P1845	Automatic Transmission Fluid Pressure Switch 5
P1846	Automatic Transmission Fluid Pressure Switch 6
P1900	Engine coolant blower motor — circuit
U1000	CAN communication line – signal malfunction
U1001	CAN communication line – signal malfunction
U1010	CAN communication line – initialization malfunction

Общие коды ошибок

[allobd2codes]

Ошибки Infiniti совместимы со следующими моделями

EX25, EX35, EX37, FX30d, FX35, FX37, FX45, FX50, G20, G25, G35, G37, I30, I35, J30, JX35, M25, M35, M37, M45, M56, Q30, Q45, Q50, Q60, Q70, QX30, QX4, QX50, QX55, QX56, QX60, QX70, QX80.